BYD ECB16S-B, Руководство оператора

Страница: 22 / 43

OPERATING
ECB16S-B/ECB18S-B 42
ECB16S-B/ECB18S-B
43 OM-ECB16/18S-B2019001-EN
5. Indicators
1
2
3
No. Name Descriptions
1 Error Indicator Indicator related to error, which appears in the case of error.
2 Overheating Indicator Indicator related to the temperature, which appears when some components are overheated.
3 Battery Failure Indicator Indicator related to the battery, which appears in the case of low battery and battery failure.
6. Trouble-shooting Methods
The following table contains all the error messages that could be shown in the multifunction
display. Please refer to the trouble shooting method for solution when the following error occurs.
After taking the recommended measures, contact the service personnel if the error message
reappears and repeats more than 3 times.
Warning message Solution
Drive
LOGIC FAILURE #1 If the battery is low, charge the battery. If battery charge is normal, restart the forklift.
D LOGIC FAILURE #3 Restart the forklift.
VMN LOW/VMN HIGH Restart the forklift.
MASTER KO Restart the forklift.
STBY I HIGH Restart the forklift.
ENCODER ERROR Restart the forklift.
INCORRECT START Return the gear switch to Stop and restart the forklift
CAP CHARGE Restart the forklift.
THERMIC SENSOR KO Restart the forklift.
Lift
LOGIC FAILURE #1 If the battery is low, charge the battery. If battery charge is normal, restart the forklift.
LOGIC FAILURE #3 If load exceeds the rated capacity, stop lifting. Otherwise restart the forklift.
VMN LOW/VMN HIGH Restart the forklift.
ENCODER ERROR Restart the forklift.
THERMIC SENSOR KO Restart the forklift.
STBY I HIGH Restart the forklift.
PUMP KO Move the control lever to the initial position and restart the forklift.
Acceleration
VACC NOT OK Check if the accelerator will return normally and restart the forklift
PEDAL WIRE KO Restart the forklift.
Others
CONTACTOR OPEN Restart the forklift.
AUX OUTPUT KO Restart the forklift.
BACKWARD Switch off the forklift, return the lever to Stop position and restart the forklift
NO CAN MESSAGE #3 Restart the forklift.
Battery WRONG SET BATTERY Restart the forklift.
Temperature
HIGH TEMPERATURE Shut down the forklift for 5 minutes and restart it
HIGH MOTOR TEMPERATURE Shut down the forklift for 5 minutes and restart it
HIGH TEMPERATURE
Shut down the forklift for 5 minutes and restart it
HIGH MOTOR TEMPERATURE Shut down the forklift for 5 minutes and restart it
TRANSPORTING LOADS
Loading
1. Load on the ground
(1) Drive the forklift carefully up to the load and brake the forklift to a stop.
(2) Tilt the mast forward and lower the forks.
。
(3) Insert the forks under the load.
(4) Raise the forks above the ground and tilt the mast backwards.
(5) When transporting, drive with caution, pay attention to the route condition and to the
people ahead and maintain a proper driving speed. Transport the load to the designated
place.
2. Load on the high shelf
(1) Drive the forklift carefully up to the load and brake the forklift to a stop.
(2) Set the mast in the vertical position and raise the forks to the bottom of the load.
(3) Insert the forks under the load.
(4) Raise the load until it has left the shelf completely.
(5) Set the driving direction to reverse and release the brake.
(6) Reverse the forklift with caution at a low speed until the forklift leaves the stacking area.
(7) Lower the forks above the ground and tilt the mast backwards.
(8) When transporting, drive with caution, pay attention to the route condition and to the
people ahead and maintain a proper driving speed. Transport the load to the designated
place.
Danger
(1) When approaching the load, do not travel at high speed to avoid crashing.
(2) Do not stay beneath the raised load.
Caution
(1) When transporting the load, the load should be securely fastened on a pallet with the
gravity center well centered.
(2) If the front mast is tilted backwards, the forks might damage the load or might not enter
fully under the load and cause danger.
Note
Before starting the forklift, pull up the emergency disconnect switch.