BYD ATTO 3 2022 Скачать руководство пользователя страница 91

Страница: 91 / 201

• After the connection is made,

discharge begins and respective

information is displayed on the

instrument cluster.

Stopping discharging

• Stopping discharging

• Disconnect the load, unplug the

connector, reinsert the port cover and

close the port hatch (refer to home

portable AC charging process*).

• Store the equipment properly.

Charging Port Electric

Lock Control Function

• The vehicle's charging port features an

anti-theft function during the charging

and discharging process. This function

is disabled by default. To enable it, go to

the charging port lock setting interface

by tapping on →

New energy

→

Charge Settings

, and tap on Enable to

turn on the anti-theft function.

• After it is enabled, users can unlock

and pull out the charging connector as

follows:

• When it is OFF, press the smart key

unlock button to unlock it;

• Press the door handle microswitch to

unlock;

• Press the center console lock below

the window inside the driver's door to

unlock it.

CAUTION

•After unlocking the charging connector,

it can be pulled out within 30 seconds.

After 30 seconds, it will lock again.

Charging Port Emergency

Unlocking

• When the electric lock fails and the

charging connector cannot be pulled

out, the lock can be manually unlocked

by pulling out the charging connector.

• Open the hood and find the inhaul

cable, and pull it to unlock the charging

connector.

Driving Range Display

• To improve driving experience, the

vehicle features a function to select the

"Driving Range Display Mode", which is

"Standard" by default.

• Set the mode in "Multimedia →

New Energy → Energy Management →

Driving Range Display Mode".

• Standard mode: The driving range is

displayed based on the result of the

comprehensive working condition

test.

• Dynamic mode: The estimated driving

range is displayed based on the

available battery power and current

average power consumption.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды