BYD ATTO 3 2022 Скачать руководство пользователя страница 89

Страница: 89 / 201

3. Stopping charging

• Stopping charging:

• When early stop is set or charging

has been completed, the charger will

automatically stop.

• Double tap the unlock button within

3 seconds or press the door handle

microswitch to stop charging.

• Disconnecting the coupler:

• Press the door handle microswitch

while carrying the smart key and pull

out the charging coupler.

• Place the charging coupler in its

designated position.

• Reinsert the cover and close the port

hatch.

REMINDER

•If the charging port plug is fully open,

do not close the charging port cover

completely.

CAUTION

•If the charging coupler cannot be

removed after unlocking, a few more

unlocking attempts can be tried. If it

still cannot be removed, emergency

unlocking can be tried. Refer to the

charging port emergency unlocking

procedure in the lock control.

•To unlock during DC charging, press

the unlock button twice within 3

seconds for the operation to be

successful.

•For specific charging precautions,

refer to the charging instructions.

WARNING

•

For specific charging safety warnings,

refer to the charging instructions.

Smart Charging Function

• When the manager detects that the low

voltage battery capacity is low, it can be

charged by the power battery, so it is

normal that the SOC and driving range

displayed decrease when the vehicle is

powered on after an idle period.

REMINDER

•When the vehicle lies idle for long pe-

riods, it is normal that smart charging

takes place.

•Power for smart charging comes from

the power battery pack, so it is nor-

mal that an SOC decrease is noticed

when the vehicle is powered on.

Discharging Equipment*

• This vehicle features a vehicle to load

(VTOL) function.

REMINDER

•This function is recommended to be

used only when SOC is high.

•This function will be limited when the

vehicle is using external discharge or

when power is low.

•When ignition status is OFF and

VTOL is connected without output

for a long time, the vehicle's static

power consumption increases. It is

recommended that the discharging/

charging connectors are removed

when the device is not in use.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды