BYD ATTO 3 2022 Скачать руководство пользователя страница 144

Страница: 144 / 201

143

IN-CAR DEVICES

• In ventilation mode, the system

introduces the natural wind from

outside, which is suitable for spring and

autumn.

REMINDER

•A/C unpleasant smell:

It is normal that there may be a

damp and moldy smell just after

the A/C is turned on. That is due to

condensation that remains in the

evaporator and is not blown dry.

•How to prevent it:

Turn off the A/C and enable

natural ventilation before parking

to keep the air inside the vehicle

relatively dry.

Check, clean or replace the air

filter regularly.

Keep the cabin clean.

•If the unpleasant smell persists,

contact a BYD authorized dealer or

service provider for repair.

•It is normal that the A/C blower keeps

running after the vehicle is locked.

That is because the condensed water

on the surface of the evaporator

needs to be dried to prevent mold

fermentation.

Vents

Front Center Vent

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Front Side Vents

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Rear Side Vents

• Move the knob to adjust airflow or to

open/close the vent.

• Toggle left/right to adjust airflow

direction.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды