BWT Perla Hybrid Скачать руководство пользователя страница 81

Страница: 81 / 84

A 1 3 Installation

Failure to follow the installation instructions will

adversely affect the product life of the hoses and

void the warranty in the event of damage.

correct

wrong

correct

A 1 3 1 Installation instructions

The straight path

must measure at least 30 mm.

The bending radius

must be at least 50 mm.

Never twist or pull the corrugated hoses.
During installation and the period thereafter, the

hoses must not be subject to any external pressure

or elongation.

►

Only use matching spanners for the hexagon

nuts. Do not use a pipe wrench!

►

Join the water softener and Multiblock with both

corrugated hoses and seal the connections.

Hose for hard water (outgoing arrow on Multiblock,

ingoing arrow on softener).

Hose for soft water (outgoing arrow on softener,

ingoing arrow on Multiblock).

Note:

According to DIN 1988, the flushing water and

overflow hoses must be connected to the sewage

water system at least 20 mm above the highest

waste water level (unimpeded drainage).

Содержание Perla Hybrid





















































































Результаты поиска

Содержание Perla Hybrid

Отзывы:

Бренды по названию

Популярные бренды

BWT Perla Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Perla Hybrid

Отзывы:

Бренды по названию

Популярные бренды