BWT Perla Hybrid Скачать руководство пользователя страница 62

Страница: 62 / 84

12 3 Remote operation of the product

via the home network (LAN / Wi-Fi)

You can operate the product remotely if it is connect-

ed to the home network via LAN or Wi-Fi.

NOTE

►

While operating the product via remote

connection, you must not change this

connection, otherwise access is no longer

possible.

►

The product and mobile device must be

in the same network.

►

To enable data transfer, the following

port must be open on your router: TLS /

SSL port 443

Requirements

●

The product was successfully registered.

●

The login code you received after registration

is available.

●

The connection via LAN or Wi-Fi is active and

working.

►

Open a web browser on a device connected to

the network.

►

Enter the IP address of the product into the

address bar in the browser. You can find this

information here:

Info > Connection status

►Confirm your entry.

►

Enter the login code received via e-mail to estab-

lish the connection.

A connection to the product is established.

►

Operate your product via the remote connection

in the same way as you would via the display on

the product.

NOTE

►

While operating the product via remote

connection, you must not change this

connection, otherwise access is no longer

possible.

►

Holiday mode can only be activated via

remote connection, not deactivated.

Содержание Perla Hybrid





















































































Результаты поиска

Содержание Perla Hybrid

Отзывы:

Бренды по названию

Популярные бренды

BWT Perla Hybrid, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Perla Hybrid

Отзывы:

Бренды по названию

Популярные бренды