AIR-EAGLE
®
SR PLUS
2.4 GHz RF Transmitter
MODEL 36UE-HH-9
BATTERY CHARGE STATUS
Hold the P/Shift button then tap button 1 and release both buttons to
see the current charge level. Note that you should give about 1 second
delay before pressing button 1.
High
TX LED blinks GREEN 4 times
Med-High
TX LED blinks GREEN 3 times
Med-Low
TX LED blinks GREEN 2 times
Low
TX LED blinks RED 1 time
Needs charged
TX LED blinks RED while transmitting and
after any button released
FREQUENCY PROGRAMMING
Please read through these instructions completely before beginning
programming procedure!
At any time, you can check the current frequency setting by depressing
the P/Shift button, for approximately 5 seconds, until the TX LED is
illuminated
RED
. Then release the P/Shift button and watch as the TX
LED stays
RED
for about 10 seconds, goes out, then begins to blink. The
TX LED will blink
RED
one, two, three or four times for Frequencies 1 thru
4, or will blink
GREEN
one, two, three or four times for Frequencies 5 thru
8 accordingly. See table below for clarification.
LED Flashes:
Indicates Unit is Operating On:
RED – one time
Frequency 1
RED – two times
Frequency 2
RED – three times
Frequency 3
RED – four times
Frequency 4
GREEN – one time
Frequency 5
GREEN – two times
Frequency 6
GREEN – three times
Frequency 7
GREEN – four times
Frequency 8
To change the setting, follow these steps:
To select from Frequencies 1 thru 8:
1.
Depress the P/Shift button until the TX LED is illuminated
RED
.
(Approximately 5 seconds)
2.
Release the P/Shift button, then while the TX LED is still
illuminated
RED
, depress button #1 to select “Frequency 1” or
button #2 to select “Frequency 2” etc. If the transmit LED goes
out before you have selected a network, no settings will have
changed,
and
the LED will blink corresponding to the frequency
that the TX is currently set to. You must then begin again at
step 1 if you wish to change the current setting.
3.
The TX LED will blink to confirm that your frequency selection
has been accepted, and then will go out. For instance, if you
have selected Frequency #1, the TX LED will blink
RED
once
to confirm. If you have selected Frequency #6, the TX LED
blinks
GREEN
two
times
to confirm.
Programming is now complete and the transmitter is active for normal
operation.
You may repeat the above procedure if you wish to change the frequency
at any time. See note* in SPECIFICATIONS.
POWER LEVEL PROGRAMMING
At any time, you can check the current power level by depressing the
P/Shift Button, for approximately 8 seconds, until the TX LED starts
BLINKING
GREEN
. Then release the buttons and watch as the TX
continues to blink for 10 seconds, goes out, then begins to blink again.
The TX LED will blink
GREEN
one, two, three or four times corresponding
the power level setting (see table below)
LED Flashes:
Indicates Unit is Set To:
GREEN – one time
Power Level 1 – Approx 100 Ft Range
GREEN – two times
Power Level 2 – Approx 250 Ft Range
GREEN – three times
Power Level 3 – Approx 400 Ft Range
GREEN – four times
Power Level 4 – Approx 600 Ft Range
To change the setting, follow these steps:
To select a power level:
1.
Depress the P/Shift Button until the TX LED is
BLINKING
GREEN
(Approximately 8 seconds)
2.
Release the P/Shift Button, then while the TX LED is still
blinking
GREEN
, depress button #1 to select “Power Level 1”
or button #2 to select “Power Level 2” etc. If the transmit LED
goes out before you have selected a power level, no settings
will have changed,
and
the LED will blink corresponding to the
power level the TX is currently set to. You must then begin
again at step 1 if you wish to change the current setting.
3.
The TX LED will blink to confirm that your power level selection
has been accepted, and then will go out. For instance, if you
have selected Power Level #1, the TX LED will blink
GREEN
once to confirm. If you have selected Power Level #3, the TX
LED blinks
GREE
N
three times to confirm.
SPECIFICATIONS
Keypad
Durable Sealed Membrane Keypad –
Eliminates Dust, Dirt and Moisture
Failures
Enclosure
ASA/Polycarb Blend – IP54 –
Not
Water Proof!
Power Requirements
Charging cable (included) Micro USB
connector to USB A type – 5 volts 1
amp
Battery Type
Internal Sealed Lithium Rechargeable.
Capacity 3.7V 2000mAh
Battery Life
(Active Usage)
Up to 2 months
Battery Life
(Sleep Mode)
Up to 6 months
Battery Recharge Time
Approximately 3 to 4 Hours
Transmit Frequency
2.4GHz Spread Spectrum
Transmit Channels
Eight Independent Network
Frequencies
RF Output Power
User Selectable from 1mW - 60 mW
Max Transmit Range
User-Selectable from 100 - 600 Feet
Note: Range figures are estimates, based on free-air terrain with
limited sources of interference. Actual range will vary based on
transmitting power, orientation of transmitter and receiver, height
of transmitting antenna, height of receiving antenna, weather
conditions, interference sources in the area, and terrain between
receiver and transmitter, including, but not limited to, indoor and
outdoor structures such as walls, metal objects, trees, buildings,
hills, and mountains
Operating Temperature
-40
o
F to +185
o
F