BVM GO FLY GOLD Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

background image

Ultra Bandit EVO

Assembly & Operation Manual

BVM ® 2019

15

11/12/2019

On some mounts it may be necessary to drill
new holes to clear engine rails.

NOTE: You can also notch the rails to fit.

New mounting holes for the KingTech K-210
strap.

INSTALL ENGINE ASSESSORIES



Mount the ECU and Fuel Pump on the

Equipment  Board  just  forward  of  the
intakes.  The  ECU  battery  is  mounted  on
the tray in the nose area.

NOTE: Here are a few examples.

KingTech Installation

JetCat Installation

«
...
17
18
19
20
21
...
»

Содержание GO FLY GOLD
























Отзывы:

Нет отзывов

Похожие инструкции для GO FLY GOLD

Flyeaglejet AT3

Бренд: Fly Eagle Jet Страницы: 9

Бренд: marklin Страницы: 28

Бренд: H-KING Страницы: 12

Z-Scale Ford F6 Truck Kit

Бренд: EA Electronics Страницы: 2

Бренд: TAMS Страницы: 17

Бренд: bruder Страницы: 2

Бренд: LEGO Страницы: 84

Бренд: C&C Models Страницы: 23

Бренд: Radica Games Страницы: 2

Бренд: Trix Страницы: 76

Бренд: QABA Страницы: 4

F-35 Lightning II Joint Strike Fighter

Бренд: Freewing Страницы: 19

Бренд: Fisher-Price Страницы: 6

Бренд: AE Страницы: 38

Бренд: Canon Страницы: 8

CREATIVE PARK Yajirobe

Бренд: Canon Страницы: 4

Floral Teddy Bear

Бренд: Canon Страницы: 5

CREATIVE PARK Zebra

Бренд: Canon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды