L
L1
L2
L
L1
L2
L
L1
L2
L
CAUTION:
Verify power is OFF to switch
before proceeding.
IMPORTANT NOTES
TOGGLE SWITCH TECHNICAL SPEC.
TOGGLE SWITCH ST YLE:
STANDARD 2 WAY SWITCH.
RATED AT 10AX 250V~ AC ONLY.
1.
Before commencing work, isolate the mains power
supply and remove the fuse in the fuse box or switch
off the circuit breaker in the consumer unit.
6.
Turn power back on.
2.
If unit is to be used as a replacement for an existing
product, remove existing unit from its location and
disconnect the wiring.
5.
To reduce the risk of discolouration or tarnishing, avoid
installation on wet plaster.
1 GANG 2 WAY 10AX AND TOGGLE SWITCH
2 GANG 2 WAY 10AX AND TOGGLE SWITCH
3 GANG 2 WAY 10AX AND TOGGLE SWITCH
INSTALL ATION
B
UST
ER
ANDPUNC
H
.C
O
M
E
L
E
CT
R
ICI
T
Y
1
G
,
2
G, 3G &
4
G SWITC
H
S
KU#
AUZ-TO-CO-1G-XX-A
**
,
AUZ-TO-CO-2G-XX-A**
,
AUZ-TO-CO-3G-XX-A**
, AUZ-TO-CO-4G-XX-A
*
*
4 GANG 2 WAY 10AX AND TOGGLE SWITCH
Note:
To ensure your toggles operate in the same orientation for on and
o
ff for the top and bottom rows, you need to wire your top row of
toggles
in reverse order to the bottom row. This means your Live will
now be wired
into L2 and your Neutral will be wired into L1.
i)
Please ensure screws are sufficiently tight to support the
product but please do not over tighten as this may cause
some deformation to the plate or damage the screw.
ii) Do NOT use a standard screw driver to tighten the coin
caps. This may damage the cap and is not covered under
warranty. Plastic coin cap tool must be used by hand only.
Use a cross head electric
or manual screwdriver to
fit the special countersunk
screws until tight.
3.
4a.
4a.
By hand, screw the coin
caps into the end of the
screws. Use the plastic coin
cap tool to fully tighten the
coin caps i).
4b.
4b.
Connect the wires as shown in appropriate wiring
diagrams. Use green/yellow sleeving on earth conductors
that are not insulated. Ensure terminals are properly
tightened and no bare wire is visable. Push back unit into
moulding box making sure conductors are not trapped.
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
L1
L2
L
Please read before installing.
All wiring and installation must adhere to the latest
local and national wiring rules - e.g.AS/NZS 3000 in
Australia & New Zealand;
This product is suitable for indoor use only.
Must be installed by a licensed electrician;
Do not exceed the rated power input
specification;
1.
2.
3.
4.
APPROVAL NO. SAA-171697-EA
WARNING:
The two mounting screws on the
faceplate must be well tightend to maintain the
earthing continuity. Check their earthing continuity by
multimeter before screw on the decorative cap. The
resistance between the two mounting screws must
not exceed 0.1
Ω
.
TO EARTH
TERMINAL
IN BOX
TO EARTH
TERMINAL
IN BOX
NOTE:
The plate must be earthed at the earth point
