Bush Hog HT417 Скачать руководство пользователя | Manualshive

Страница: 72 / 82

background image

OPERATION

HT417/HT417H 05/22

Operation Section 4-26

© 2022 Alamo Group Inc.

OPERA

TION

Reduce speed before turning or applying the brakes.
Ensure that both brake pedals are locked together
when operating on public roads.

OPS-U- 0023

13.4 Hauling the Tractor and Implement

Before transporting a loaded tractor and implement,
measure the height and width dimensions and gross
weight of the complete loaded unit. Ensure that the
load will be in compliance with the legal limits set for
the areas that will be traveled through.

OPS-U- 0024

Use adequately sized and rated trailers and equip

-

ment to transport the tractor and implement. Con

-

sult an authorized dealer to determine the proper
equipment required. Using adequately sized chains,
heavy duty straps, cables and/or binders, securely
tie down both the front and rear of the tractor utiliz

-

ing the proper tie down locations as specified by the
tractor manufacturer.

OPS-U- 0025

«
...
70
71
72
73
74
...
»

Содержание HT417



















































































Отзывы:

Нет отзывов

Похожие инструкции для HT417

Бренд: zarges Страницы: 8

Бренд: Toya Страницы: 32

Бренд: Hailo Страницы: 88

Бренд: Confer Plastics Страницы: 4

Бренд: pixima fontanot Страницы: 72

Бренд: zarges Страницы: 5

Бренд: Schou Страницы: 103

Бренд: PLAYSTAR Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды