background image

The rotors do not turn, and cannot be turned
either way by hand:

Failure of the motor

Repair or change motor

The rotors do not turn, and cannot be turned
by hand either way:

Rotors are jammed, stuck or seized

Free the rotors

Check for signs of overheating
(discolouration) and contact Busch Service for
a service/ dismantling for repair

Foreign substances in the pump

Dismantle pump to clean and repair

Abnormal sounds or vibrations:

STOP BLOWER IMMEDIATELY !!

Excessive wear of bearings

Change bearings

Too little gear oil in the pump, or oil in the
pump is worn

Top up with oil/ Change gear oil

Resonance of piping

Provide support for the piping or use flexible
connections

**Abnormal increase of discharge pressure

Refer to cause marked with **

Leakage

Find and stop leaks

Synchronising the rotors

Have the vacuum pump repaired (Busch
service)

Foreign particles in the gear housing

Have the vacuum pump repaired (Busch
service)

Failure of non-return valve

Change non-return valve

Abnormal heat

Abnormal increase of discharge pressure

Refer to causes marked with **

Rotational speed of blower and/ or motor too
low (when using a frequency converter)

Check the minimal admissible rotational speed
and correct

Too much gear oil in the housing

Fill in oil only to the target circle of the oil
sight glass, while the blower is switched off

Ambient temperature too high

Increase ventilation of the machine room/
increase rotational speed (ventilation) of
motor

Blockage of the suction inlet or filter

Clean suction inlet, and clean or change filter

Excessive wear of rotors and consequently
increase of rotor tolerances

Install filter and dismantle blower for repair

Have the vacuum pump repaired (Busch
service)

**Abnormal increase of discharge pressure

Blockage of discharge pipe

Clean discharge pipe

Blockage of system piping

Clean system piping

Primary pump failure

Have the vacuum pump repaired (Busch
service)

Oil leaks

Too much oil in the pump

Fill up oil only to the target circle of the oil
sight glass, while the blower is switched off

Worn or broken mechanical seals
(oil-lubricated single mechanical seals) do not
apply to WY pumps

Change mechanical seals

Ambient conditions and vacuum combined
with pressure operation and high dP

Fit an oil separator, ensure adequate
ventilation

Pump has been tilted or is not level

Install the pump on a horizontal surface

Oil level in the seal housing fluctuates
abnormally (Applies to pumps equipped with
a drop oiler)

Worn or broken mechanical seals

Change mechanical seals

Troubleshooting

Page 19

Содержание WY 4500 C

























Отзывы: