background image

6 | Electrical Connection

20 | 44

Instruction Manual R5 RA 0165-0305 D_EN_en

NOTICE

Incorrect connection.
Risk of damage to the variable speed drive!

The wiring diagrams given below are typical. Check the connection instructions/diagrams.

6.4

Wiring Diagram Three-Phase Motor

NOTICE

Incorrect direction of rotation.
Risk of damage to the machine!

Operation in the wrong direction of rotation can destroy the machine in a short time! Prior to
start-up, ensure that the machine is operated in the right direction.

Determine the intended direction of rotation with the arrow (stuck on or cast).

Jog the motor briefly.

Watch the fan wheel of the motor and determine the direction of rotation just before the fan
wheel stops.

If the rotation of the motor must be changed:

Switch any two of the motor phase wires.

Delta connection (low voltage):

Star connection (high voltage):

Double star connection, multi-voltage motor
with 9 pins (low voltage):

Star connection, multi-voltage motor with 9
pins (high voltage):

Double star connection, multi-voltage motor
with 12 pins (low voltage):

4

4

4

Star connection, multi-voltage motor with 12
pins (high voltage):

4

4

4

Содержание RA 0165 D













































Отзывы: