BUSCH R5 RD 0200 A Скачать руководство пользователя

Страница: 35 / 40

Technical Data | 13

Instruction Manual R5 RD 0200-0360 A_EN_en

35 | 40

Technical Data

RD 0200 A

RD 0240 A

Nominal pumping speed
(50Hz / 60Hz)

m³/h

160 / 190

200 / 240

ACFM

94 / 112

118 / 141

Ultimate pressure
(without gas ballast valve)

hPa (mbar) abs.

0.1

TORR

0.075

Ultimate pressure
(with gas ballast valve)

hPa (mbar) abs.

0.5

TORR

0.375

Nominal motor speed
(50Hz / 60Hz)

min

-1

1500 / 1800

RPM

Permitted motor speed range

min

-1

1200 … 1800

RPM

Nominal motor rating
(50Hz / 60Hz)

3.0 / 4.2

4.0 / 4.2

- / 5.6

Power consumption at 100 mbar –
75 TORR (50Hz / 60Hz)

2.9 / 3.8

3.5 / 4.3

- / 5.1

- / 5.4

Power consumption at ultimate
pressure (50Hz / 60Hz)

1.9 / 2.3

2.0 / 2.5

- / 3.1

- / 3.4

Noise level (ISO 2151)
(50Hz / 60Hz)

dB(A)

68 / 70

68 / 72

Water vapor tolerance max. (with
gas ballast valve) (50Hz / 60Hz)

hPa (mbar)

40 / 100

TORR

- / 75

Water vapor capacity (with gas
ballast valve) (50Hz / 60Hz)

kg / h

4,0 / 8,3

5,2 / 11,4

Lbs. / h

8.8 / 18.3

11.5 / 25.1

Max. allowable pressure in the oil
mist separator

hPa (mbar) abs.

1600

TORR

1200

Max. allowable gas inlet
temperature

°C

≤

50 hPa (mbar) abs.

►

150

°F

≤

37.5 torr

►

302

°C

50 hPa (mbar) abs.

►

°F

37.5 torr

►

176

Ambient temperature range

°C

5 ... 40

°F

41 … 104

Ambient pressure

Atmospheric pressure

Oil capacity

qts.

7.5

Weight approx.

175

Lbs.

386

Содержание R5 RD 0200 A









































Результаты поиска

Содержание R5 RD 0200 A

Отзывы:

Похожие инструкции для R5 RD 0200 A

Бренды по названию

Популярные бренды

BUSCH R5 RD 0200 A, Инструкция по эксплуатации

Результаты поиска

Содержание R5 RD 0200 A

Отзывы:

Похожие инструкции для R5 RD 0200 A

Бренды по названию

Популярные бренды