background image

Maintenance | 8

Instruction Manual R5 RD 0200-0360 A_EN_en

25 | 40

Change the oil, the oil filter (OF) and the
exhaust filter (EF).

Clean the machine and air heat exchanger
from dust and dirt (see Air Heat Exchanger
Cleaning
 [

 29]).

Clean the gas ballast valve (GB).

Max. after 4000 hours,

at the latest after 1

year

For RD 0200 A:

max. after 3600

hours, at the latest

after 6 months

For RD 0240 A:

max. after 3000

hours, at the latest

after 6 months

For RD 0300 A:

max. after 2400

hours, at the latest

after 6 months

For RD 0360 A:

max. after 2000

hours, at the latest

after 6 months

Contact Busch for an inspection.
If required, overhaul the machine.

Every 5 years

* Service interval for synthetic oil, shorten the interval when using mineral oil, contact Busch Service

8.2

Oil Level Inspection

Shut down the machine.

When the machine is stopped, wait 1 minute before checking the oil level.

MAX

MIN

MAX

MIN

MAX

MIN

Fill up if necessary, see Oil Filling [

 14].

8.3

Oil and Oil Filter Change

NOTICE

Use of an inappropriate oil.
Risk of premature failure!
Loss of efficiency!

Only use an oil type which has previously been approved and recommended by Busch.

Содержание R5 RD 0200 A









































Отзывы: