BUSCH R 5 RA 1000 B Скачать руководство пользователя страница 14

Страница: 14 / 40

5 | Installation

14 / 40

0870201062_RA1000-1600B_Ex_-0007_IM_en

5.2.3 Cooling Water Connection (Optional)

Water-oil heat exchanger without inlet accessories

WHE

CWO

CWI

CWO

CWI

WHE

Water-oil heat exchanger with inlet accessories

WBV

CWI

Cooling water inlet

Pressure switch

CWO

Cooling water outlet

WBV

Water bypass valve

WHE

Water-oil heat exchanger

Water filter

Thermostatic valve

Solenoid valve

The thermostatic valve (TV) is used to control the water flow in order to keep a stable
machine temperature.

The factory default adjustment of the thermostatic valve (TV) is set in position 2 (approx.
75°C oil temperature).

The pressure switch (PS) is used to monitor the presence of water at the cooling system
of the machine.

When the pressure switch detects a pressure lower than 2 bar, the machine must be
stopped.

The water bypass valve (WBV) is used at the first machine start-up. At that moment it
should be open (approx. 90 seconds) to prime the water heat exchanger, afterwards it
should be closed.

The solenoid valve (MV) is used to stop the cooling water circulation when the machine
is not running.

• Connect the cooling water connections (CWI / CWO) to the water supply.

Connection size:

– 19 mm hose (CWI / CWO)

• If necessary, electrically connect the pressure switch (PS), see

Wiring Diagram Pres-

sure Switch of Water-oil Heat Exchanger (Optional) [

►

21]

• If necessary, electrically connect the solenoid valve (MV).

• Make sure that the cooling water complies with the following requirements:

Min. supply capacity

l/min

Water pressure

bar

2 ... 6

Supply temperature

°C

+5 ... +35

Required pressure differential across supply
and return

bar

≥

Содержание R 5 RA 1000 B









































Результаты поиска

Содержание R 5 RA 1000 B

Отзывы:

Похожие инструкции для R 5 RA 1000 B

Бренды по названию

Популярные бренды

BUSCH R 5 RA 1000 B, Инструкция по эксплуатации

Результаты поиска

Содержание R 5 RA 1000 B

Отзывы:

Похожие инструкции для R 5 RA 1000 B

Бренды по названию

Популярные бренды