background image

2 | Product Description

6 / 28

Instruction Manual MINK MM 1402-1502 AV_EN_en

2.3.1 Gas Tight Version

WARNING

Media potentially dangerous.

Risk of poisoning!

Risk of infection!

• Wear appropriate personal protective equipment in case of high concentration of the

medium in the ambient atmosphere of the machine.

The gas tight version is a design option for applications where the process gas remains in
the machine and does not escape to the environment.

It is a very important feature for applications where gases potentially dangerous to hu-
man health are not allowed and the concentration of the process gas must not exceed
the admissible values of the ambient atmosphere of the machine.

This machine is specifically equipped with:

– pressure relief lines

– collecting lines

– shaft seal rings.

Requirements for a proper functioning:

Ambient pressure

The gas tight machine requires an ambient pressure at the gas
discharge during the whole operation range of +/- 200 hPa
(mbar), unless otherwise specified on the nameplate.

Leakage rate

The machine is not absolutely gas tight.
The leakage rate of the machine described in this manual is of
0.1 hPa l/s (mbar l/s) at a suction pressure of 250 mbar. It can
considerably increase up to prohibited pressure values at the
gas inlet/outlet due to used shaft seal rings or clogged pres-
sure relief lines.

Ambient environment

Closed air cooling systems are not suitable and therefore pro-
hibited.

• Make sure that the machine is sufficiently vented (see 

In-

stallation Conditions [

 9]

).

2.3.2 Aqua Version

The Aqua version is a design option for conveying condensable vapours (water).

This machine is specifically equipped with:

– corrosion protection coating

– optional condensate drain (CD) in the internal silencer.

2.4 Start Controls

The machine comes without start controls. The control of the machine is to be provided
in the course of installation.

The machine can be equipped with a soft-starter.

Содержание MINK MM 1402 AV





























Отзывы: