BUSCH LM 0100 A Скачать руководство пользователя страница 9

Страница: 9 / 40

Installation | 5

Instruction Manual DOLPHIN LM 0100-0800 A, LT 0130-0750 A_EN_en

9 | 40

Installation

5.1

Installation Conditions

NOTICE

Use of the machine outside of the permitted installation conditions.
Risk of premature failure!
Loss of efficiency!

●

Take care that the installation conditions are fully complied with.

●

Make sure that the environment of the machine is not potentially explosive.

If there is Ex(o) sign written on the nameplate:

●

Please refer to the ATEX supplement for additional safety information.

●

Make sure that the ambient conditions comply with the

●

Make sure that the environmental conditions comply with the protection class of the motor and
the electrical elements.

●

Make sure that the installation space or location is protected from weather and lightning.

●

Make sure that the installation space or location is vented such that sufficient cooling of the ma-
chine is provided.

●

Make sure that cooling air inlets and outlets of the motor fan are not covered or obstructed and
that the cooling air flow is not affected adversely in any other way.

●

Make sure that enough space remains for maintenance work.

●

Make sure that the machine is placed or mounted horizontally on a flat surface.

●

Make sure that the machine is connected to an operating liquid system, see

Operating Liquid Con-

●

Make sure that all provided covers, guards, hoods, etc. are mounted.

In case of a machine delivery without motor:

●

Make sure that the coupling is correctly aligned, see

Fitting the Coupling

[

➔

14].

If the machine is installed at an altitude greater than 1000 meters above sea level:

●

Contact your Busch representative, the motor should be derated or the ambient temperature
limited.

Содержание LM 0100 A









































Результаты поиска

Содержание LM 0100 A

Отзывы:

Похожие инструкции для LM 0100 A

Бренды по названию

Популярные бренды

BUSCH LM 0100 A, Инструкция по эксплуатации

Результаты поиска

Содержание LM 0100 A

Отзывы:

Похожие инструкции для LM 0100 A

Бренды по названию

Популярные бренды