BUSCH COBRA NC 0950 A Скачать руководство пользователя страница 38

Страница: 38 / 44

13 | Technical Data

38 | 44

Instruction Manual COBRA NX 0950 A WCV_EN_en

Technical Data

NX 0950 A WCV

Pumping speed (72Hz)

m³/h

950

ACFM

560

Ultimate pressure
(without gas ballast)

hPa (mbar) abs.

≤

0.01

TORR

≤

0.0075

Ultimate pressure
(with gas ballast)

hPa (mbar) abs.

≤

0.05

TORR

≤

0.0375

Nominal motor rating

18.5

Nominal motor speed (72Hz)

min

-1

4320

RPM

4320

Max. intensity

Circuit breaker (MCCB)

C-50 (SCCR 10kA @ 400V)

Noise level (EN ISO 2151)

dB(A)

≤

Ambient temperature range

°C

5 … 40

°F

41 … 104

Max. allowable counter pressure at
the discharge

hPa (mbar) rel.

200

TORR

150

Max. allowable gas inlet tempera-
ture according to the inlet pres-
sure

°C

≤

50 hPa (mbar) abs.

►

200

50 hPa (mbar) abs.

►

°F

≤

37.5 Torr

►

392

37.5 Torr

►

158

Relative humidity

at 30°C

90%

at 86°F

90%

Ambient pressure

Atmospheric pressure

Cooling water requirements

See Cooling Water Connection [

➔

15]

Oil capacity - motor side

qts.

1.05

Oil capacity - suction side

qts.

1.05

Weight approx.

900

Lbs.

2000

Содержание COBRA NC 0950 A













































Результаты поиска

Содержание COBRA NC 0950 A

Отзывы:

Похожие инструкции для COBRA NC 0950 A

Бренды по названию

Популярные бренды

BUSCH COBRA NC 0950 A, Инструкция по эксплуатации

Результаты поиска

Содержание COBRA NC 0950 A

Отзывы:

Похожие инструкции для COBRA NC 0950 A

Бренды по названию

Популярные бренды