manualshive.com logo in svg

BUSCH 0659230708, Инструкция по эксплуатации, Страница: 18 / 80

Поделиться
Скачать
BUSCH 0659230708 Скачать руководство пользователя страница 18

Put the funnel (included with the detector) in the oil fill opening (3).
Fill with oil to the highest level.

Replace the oil fill cap tightly (1).

5.5 Connection to the mains power supply

The leak detector is Class 1 equipment and therefore must be earthed.

5.6 Operating for the first time

Check that the oil level of the primary pump is between the maximum and minimum

levels 

(see 5.4)

.

Attach the electrical network to the connector 

 using the power cable delivered with 

the detector.
Set the circuit breaker

 to 

I

.

Set the language, unit, time and date (the operator can modify this at a later time

 

(see

7.7.1)

).

1

2

Max
Min

3

WARNING

Risk of electromagnetic disturbance 

The product’s EMC behavior is guaranteed only if the relevant EMC standards are fol-

lowed during installation. 

Use shielded cables and connections for the interfaces in interference-prone environ-

ments.

WARNING

Hazard associated with non-compliant electrical installation

Safe operation after installation is the operator’s responsibility.

Connect the product to an installation that is compliant with local safety standards.

Do not carry out any alterations or modifications to the product on your own initiative.

For specific questions, contact your service center.

18

0870231897_0001_IM_en

Installation

Содержание 0659230708

















































































Отзывы:

Нет отзывов