Burley Burley-Solo Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

Burley Burley-Solo Скачать руководство пользователя страница 7

7

Take care that you put the proper side-panel assembly on each side with

the correct side facing outward. The side rails slope gently toward the front

of the Burley-Solo, each with the trademark “Burley” facing outward. Next,

snap each side-panel assembly into place with the plastic side-panel hold-

downs at the front and rear of each side as shown on previous page.

All four side-panel hold-downs must be snapped in place before using trailer.
Otherwise side rails can shift or collapse resulting in serious injury.

Side Rail

Roll Bar

Cover Grommet

Roll-Bar Knob

Install Roll Bar and Cover

Locate the two roll-bar knobs in the hardware bag and the Wide Screen

2 -in-1 Cover™. You’ll

fi

nd the roll bar attached to the top of the fabric

child seat. Lay the cover over the side rails to ensure it is right side out,

and oriented so the rear snaps can be attached to the lower snap studs

at the rear of the Burley-Solo. Next, slip one of the roll-bar knobs through

one of the grommets on the cover. Align one end of the roll bar with its

corresponding hole on the side rail. Thread the roll-bar knob through one

side rail, and tighten it into the roll bar (see illustration below). Similarly,

thread the second roll-bar knob through the other grommet on the cover,

align the roll bar with the hole in the other side rail, and screw this roll-bar

knob into the roll bar. Carefully check that both roll-bar knobs are screwed

tightly into the roll bar.

Connect the snap hooks behind the seat to the D-Rings at the rear of the

«
...
5
6
7
8
9
...
»

Содержание Burley-Solo

























Отзывы:

Нет отзывов