manualshive.com logo in svg

Burkert 8653 AirLINE Field, Руководство по эксплуатации, Страница: 8 / 43

Поделиться
Скачать
Burkert 8653 AirLINE Field Скачать руководство пользователя страница 8

8

Basic safety instructions

Type 8653

3 

Basic safeTy insTrucTiOns

These safety instructions do not consider any contingencies or incidents which occur during assembly, 

operation and maintenance. The operator is responsible for observing the location-specific safety regula

-

tions, also with reference to the personnel.

risk of injury due to high pressure and uncontrolled movement of the actuators.

 

►

Before working on the device or system, secure the actuators against moving. 

 

►

Before working on the device or system, switch off the pressure. Vent or drain lines.

risk of injury from electric shock.

 

►

Before working on the device or system, switch off the power supply. Secure against reactivation.

 

►

Observe applicable accident prevention and safety regulations for electrical equipment.

risk of burns due to hot device parts.

 

►

Keep the device away from highly flammable substances and media.

risk of injury due to improper installation and maintenance.

 

►

Only trained technicians may perform installation and maintenance work.

 

►

Perform installation and maintenance with suitable tools only.

risk of injury due to unintentional activation and uncontrolled start-up of the device and system.

 

►

Secure the device and system to prevent unintentional activation.

 

►

Ensure that the system does not start up in an uncontrolled manner.

General hazardous situations.

To prevent injury, observe the following:

 

►

Install the device according to the regulations applicable in the country. 

 

►

Do not supply aggressive or flammable media to the media connections of the device.

 

►

Do not supply liquids to the media connections of the device.

 

►

After the process is interrupted, restart in a controlled manner. 

 

Observe sequence:

 

1. Connect the power supply. 

2.  Connect the pneumatic supply (with an external pressure supply, initially the external auxiliary pilot air 

[X / 12/14] and then the medium pressure [P / 1]).

 

►

Do not make any changes to the device.

 

►

Do not subject the device to mechanical loads.

 

►

Observe the general rules of technology.

english

Содержание 8653 AirLINE Field












































Отзывы:

Нет отзывов