manualshive.com logo in svg

Burkert 20010867, Руководство по эксплуатации, Страница: 10 / 42

Поделиться
Скачать
Burkert 20010867 Скачать руководство пользователя страница 10

10

Product description

Type 3281

5 

PRODUCT DESCRIPTION

5.1 

Intended area of application

The motor valve Type 3281 is designed to control the flow of liquid and gaseous media. Only clean, liquid or 

gaseous media that do not attack the valve body and seal materials may be controlled.

NOTE 

Damage to the valve body and seals due to unsuitable media.

Unsuitable media can cause damage to the valve body and seals.

 

▶

Use only suitable media.

 

▶

Check resistance in each individual case.

5.2 

Structure and function

The valve spindle is driven by a stepper motor. The rotary rotational movement of the motor is converted into 

a linear movement by means of a threaded spindle. The valve spindle is rigidly connected to the threaded 

spindle. The valve spindle is connected to a control cone.

Circular plug-in connector

Valve body

Actuator cover

Control cone

Valve spindle

Stepper motor

Wrench flat of the body 

connection

Fig. 1: 

Structure of the valve

The flow or switching of the valve is regulated by means of a stepper motor actuator, which is controlled by 

the integrated control electronics. No external motor control is required for step control.

5.2.1 

Functions of the control electronics

• Control of the valve opening by processing the external set-point values.
• Output of the valve statuses via the LED display.
• Detection of the position after power failure.  

- In the event of a power failure, the current position of the valve is retained.  

english

Содержание 20010867











































Отзывы:

Нет отзывов