background image

Page 4

ELECTRICAL REQUIREMENTS

CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.

Electrical Hook-Up

CAUTION – Improper electrical installation will damage electronic components.

1.  An electrician must provide electrical service as specified.

2.  Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3.  If plumbing is to be hooked up later be sure the brewer is disconnected from the power source.  If plumbing 

has been hooked up, the brewer is ready for Initial Set-Up.

100V & 120V

Models

CE REQUIREMENTS

• This appliance must be installed in locations where it can be overseen by trained personnel.

• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.

• Appliance shall not be tilted more than 10° for safe operation.

• An electrician must provide electrical service as specified in conformance with all local and national codes.

• This appliance must not be cleaned by water jet.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of 

this appliance by a person responsible for its safety.

• Children should be supervised to ensure they do not play with the appliance.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with 

a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

• Machine must not be immersed for cleaning.

230 VOLT CE Model

Note: 

This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate con-

ductor for chassis ground.

230 VOLT UK Model

42822.1 051110

Содержание Trifecta





















Отзывы: