Bulls Lacuba EVO 45 Sport Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 133

Bulls Lacuba EVO 45 Sport Скачать руководство пользователя страница 56

Before the first ride

MY19B103_1.0_04.01.2019

56



The rider is sitting in the optimal sitting position if
the knee cap perpendicular line runs through the
pedal axle. If the perpendicular line crosses behind
the pedal, bring the saddle forward. If the
perpendicular line crosses in front of the pedal,
bring the saddle back. Move the saddle within its
permitted displacement range only (marked on the
saddle stay).

Figure 17:

Knee cap perpendicular line

6.2

Adjusting the handlebars

90°



The handlebars must only be adjusted while the
vehicle is stationary.



Unfasten and adjust the designated screw
connections, and clamp them with the maximum
tightening torque for the clamping screws of the
handlebars.

Maximum tightening torque for the

clamping screws of the handlebars*

*if there is no other data on the component

5 Nm - 7 Nm

Table 25:

Handlebars clamping screw maximum tightening torque

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book Page 56 Tuesday, January 8, 2019 4:38 PM

«
...
54
55
56
57
58
...
»

Содержание Lacuba EVO 45 Sport






































































































































Отзывы:

Нет отзывов