manualshive.com logo in svg

Bühler technologies Nivotemp NT M-XP, Инструкция по установке и эксплуатации, Страница: 11 / 42

Поделиться
Скачать
Bühler technologies Nivotemp NT M-XP Скачать руководство пользователя страница 11

Nivotemp NT M-XP

5 Operation and control

NOTICE

The device must not be operated beyond its specifications.

5.1 Start-up procedure

The device will automatically switch on when connected to power. It will first briefly display the software version, at which time
the device will also check the built-in components. The display will then switch to displaying measurements.

The following describes the function of the display and control unit:

LEDs

Control keys

Display

If an error message appears in the display during operation, please refer to the 

Troubleshooting

 table under chapter “Service

and Repair”.

5.2 LED statuses

LEDs above the measurement display indicate the status of the switching outputs. The LEDs are permanently assigned to the
switching outputs.

The following table lists the factory settings for the liquid level and temperature switching output configuration:

2 Switching

outputs

4 Switching

outputs

6 Switching

outputs

LED 1 – yellow
Status switching output 1

Liquid Level

Liquid Level

Liquid Level

LED 2 - red 
Status switching output 2

Temperature

Liquid Level

Liquid Level

LED 3 – yellow
Status switching output 3

---

Temperature

Liquid Level

LED 4 – red
Status switching output 4

---

Temperature

Temperature

LED 5 – yellow
Status switching output 5

---

---

Temperature

LED 6 – red
Status switching output 6

---

---

Temperature

The switching characteristics of the LED (on if switching contact closed or open) can be changed.

9

Bühler Technologies GmbH

BE100023 ◦ 06/2021

Содержание Nivotemp NT M-XP











































Отзывы:

Нет отзывов