TM
User Manual
BS-GU2016P
Package Contents
The package contains the items shown below. If any items are missing,
please contact the dealer where you purchased the BS-GU2016P.
The appearance of the BS-GU2016P may vary from the illustration.
• Switch (main unit) ................................................................................................... 1
• Power cable (AC 100-240 V) ................................................................................. 1
• Power cable retainer band .................................................................................... 1
• Rubber feet ............................................................................................................... 4
• Mounting brackets................................................................................................... 2
• Screws for mounting brackets ........................................................................... 8
• Serial number stickers............................................................................................. 2
• User manual (this document) .............................................................................. 1
• Warranty ..................................................................................................................... 1
Layout
1. Indicators
Indicators are located on the front panel of the product. The functions of
each indicator are shown below.
Loop (Red)
Blinking:
Loop blocked (blinks once per second)
Off:
Normal
Power (Green)
On:
Power on
Off:
Power off
PoE (Green or Orange)
On (Green): PoE power is available
On (Orange):
Overcurrent or excessive power draw
Off:
PoE power is disabled
1000 Mbps (Green)
On:
1000 Mbps link
Blinking:
If a loop is blocked, the LED for the blocked port blinks
once per second.
Off:
100 Mbps or 10 Mbps link, no link
Link/Act (Green)
On:
Link established
Blinking:
Data transfer
If a loop is blocked, the LED for the blocked port blinks
once per second.
Off:
Link not established
2. PoE ports
These Ethernet ports support PoE. Connect devices that need
Ethernet power to these ports. Each port can supply up to 15.4 watts
with a maximum total of 120 watts for all 12 ports.
Connect Ethernet devices to the switch in ascending order of port
number. If the maximum total power for PoE exceeds 120 watts,
power to ports will be disabled in descending order by port number
until the total output power for PoE is below 120 watts.
All ports support autonegotiation. The optimal duplex mode (full
duplex or half duplex) and transfer speed (1000, 100, or 10 Mbps) are
selected automatically.
3. Uplink ports
Connect other hubs or switches to these ports. These ports don't
support PoE.
4. Loop prevention switch
This switches loop prevention on and off.
5. Power connector
Connect the included power cable to this connector.
Installation
Precautions for Installation
• Do not install the device in an unstable location such as on an unsteady
table or an inclined surface.
• Do not place another hub or object that generates heat on this unit.
• Please route all cables properly to prevent people from tripping over
them.
• Ensure the air vents on the product are not blocked by other
equipment or walls.
• Only use the power cable included with the product. Using other
power cables may result in damage or fire.
Floor or Shelf Mounting
Attach the supplied rubber feet to the bottom corners of the unit before
use.
Mounting to a Metal Surface
To mount to a metal surface, such as the side of a steel desk, use the
"BS-MGK-A Magnet Kit" (sold separately). Attach the supplied rubber feet
to the bottom corners of the unit before using the magnet kit.
Note:
- Do not put floppy discs, magnetic cards, or other magnetic storage
media near magnets. Doing so may delete or corrupt data.
- If the switch is secured by the magnet alone, it should be no more
than 75 cm (29.5 in) from the floor.
- If using the magnet kit, please do not to install the switch with the
fan on bottom for safety.
Installing on 19-inch Rack
Install as shown in the figure below by using the supplied mounting
brackets.
Mounting screws (right and left: 4 each)
19-inch rack screws (not included)
(right and left: 2 locations)
Mounting holes
Magnet mounting holes
Use screws where this section is 2 mm
or less.
φ6
1. Indicators
2. PoE ports
3. Uplink ports
5. Power connector
4. Loop prevention switch
AC IN
Power cable retainer band
Wall Mounting
To mount the unit to a wall, use 2 screws (not included) with the
dimensions shown below. Install the screws 178 mm (7 in) apart and slide
the mounting holes in the base of the BS-GU2016P over them.
2mm
3mm
