Buell XB 2010 Скачать руководство пользователя страница 525 | Manualshive

Страница: 525 / 714

background image

6.17

HEADLIGHT

GENERAL

Dual headlights are equipped with replaceable bulbs.

•

High beam headlight is located on the left side of vehicle.
and turns on and off with headlight switch.

•

Low beam headlight is located on the right side of vehicle.

•

Firebolt Models: Adjustment of individual headlight pro-
jection is accomplished by adjusting two screws located
in the headlight support.

•

Lightning and Ulysses Models: Adjustment of individual
headlight projection is accomplished by adjusting the entire
headlight assembly.

NOTES

•

Lightning/Ulysses: Low beam does not remain on when
high beam is activated. Only one headlight remains on at
any given time unless the passing lamp switch is
depressed while low beam is activated causing the high
beam to temporarily flash.

•

Firebolt: Low beam will remain on when high beam is
activated.

2

1

3

sm00400

1.

Passing lamp switch

2.

HIGH beam

3.

LOW beam

Figure 6-62. Headlight Controls

HEADLIGHT BULBS: FIREBOLT

Removal

To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)

1.

Disconnect negative battery cable.

Handle bulb carefully and wear eye protection. Bulb con-
tains gas under pressure, which, if not handled carefully,
could cause serious eye injury. (00062b)

Never touch the quartz bulb. Fingerprints will etch the
glass and decrease bulb life. Handle the bulb with paper
or a clean, dry cloth. Failure to do so could result in bulb
damage. (00210b)

2.

See

. Disconnect headlight connection (1).

3.

Remove rubber boot from headlight housing.

4.

Release wire retaining latch (5) from headlight housing
clips.

5.

Pull bulb housing from headlight housing.

Installation

NOTE

Not using the specified bulb may cause charging system
problems.

Handle bulb carefully and wear eye protection. Bulb con-
tains gas under pressure, which, if not handled carefully,
could cause serious eye injury. (00062b)

Never touch the quartz bulb. Fingerprints will etch the
glass and decrease bulb life. Handle the bulb with paper
or a clean, dry cloth. Failure to do so could result in bulb
damage. (00210b)

1.

See

. Align tabs on bulb (3) with tabs on

headlight (4). Insert bulb.

2.

Close the wire retaining latch (5).

3.

Install rubber boot on headlight housing.

4.

Connect the headlight bulb connector.

5.

Connect negative battery cable and tighten fastener to
60-70 in-lbs (6.8-7.9 Nm).

Be sure that all lights and switches operate properly before
operating motorcycle. Low visibility of rider can result in
death or serious injury. (00316a)

2010 XB Service: Electrical 6-51

«
...
523
524
525
526
527
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Baja motorsports Страницы: 20

Бренд: R&G Страницы: 4

Бренд: DAELIM Страницы: 68

Dirt Runner 90cc

Бренд: Baja motorsports Страницы: 66

Бренд: R&G Страницы: 24

Бренд: Suzuki Страницы: 26

Бренд: Spartus Страницы: 24

Daytona 955i 2002

Бренд: Triumph Страницы: 384

Бренд: SCA Страницы: 5

Бренд: KTM Power Parts Страницы: 12

Бренд: DYNATEK Страницы: 4

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 18

Бренд: R&G Страницы: 17

Бренд: Shad Страницы: 2

Бренд: Saddlemen Страницы: 2

Бренд: Saddlemen Страницы: 2

Бренд: Saddlemen Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды