Buehler 11-2180 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 37

Buehler 11-2180 Скачать руководство пользователя страница 13

IsoMet

®

1000 Front Control Panel

ZERO

INCH

MM

CHUCK

BLADE

POWER

POSITION

SPEED

IsoMet 1000

PRECISION SAW

BUEHLER

Figure 5

IsoMet

®

1000 Front Control Panel

ZERO

POSITION (ZERO)

Resets the blade position to zero. The POSITION LCD will

display 00.0.

INCH

MM

UNITS (MM / INCH)

Displays either millimeters or inches as the unit of

measurement in the POSITION LCD.

The default unit of measurement is inches. The indicator light
will light up for the unit of measure selected.

POSITION FIELD

Displays the distance of the blade from the set ZERO position.

INCREASE

Increases the blade speed in increments of 25 rpms. Press and
hold the INCREASE button for rapid speed selection.

DECREASE

Decreases the blade speed in increments of 25 rpms. Press and
hold the DECREASE button for rapid speed selection.

SPEED FIELD

Displays the blade speed in rpms. The minimum blade speed is
100 rpms. The maximum blade speed is 950 rpms.

Note:

The IsoMet

®

1000 will retain to the last selected speed.

CHUCK

CHUCK

Only used

with the Rotating Chuck accessory. Activates and

deactivates the Rotating Chuck. The indicator light will light up
when the chuck is activated.

13

MA112180_33

6/27/2005

«
...
11
12
13
14
15
...
»

Содержание 11-2180






































Отзывы:

Нет отзывов