Buderus Logalux ST1000/3 US Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

Buderus Logalux ST1000/3 US Скачать руководство пользователя страница 16

16

Installation and maintenance instructions Logalux ST400/3, 500/3, 750/3 and 1000/3 "US" • Issue 07/2005

We reserve the right to make any changes due to technical

Maintenance

8

z

Remove hexagon bolts (Fig. 16,

Item 1

) from the

manual access cover (Fig. 16,

Item 3

).

z

Remove the access cover, transport handle (Fig. 16,

Item 2

) and access cover gasket (Fig. 16,

Item 4

)

from the DHW tank.

8.2

Cleaning the DHW tank

z

Check the DHW tank interior for scale deposits
(calcium).

Should scale deposits be discovered inside the DHW
tank, proceed as follows:

z

Hose down the interior of the DHW tank with a "hard"
cold water jet (approx. 58 –

72 psi pressure)

(Fig. 17).

You can increase the cleaning effect of the jet by
heating up the DHW tank before cleaning. The
thermo-shock effect releases scale deposits more
easily from the coil type heat exchanger. Remove the
residues with a wet & dry vacuum cleaner with plastic
suction tube or flush debris through the tank drain.

Fig. 16

Removing the access cover

Item 1:

Hexagon bolts

Item 2:

Transport handle

Item 3:

Hand hole cover

Item 4:

Manual access cover gasket

Item 5:

Magnesium anode

3

2

1

4

5

CAUTION!

SYSTEM DAMAGE

through damaged surface finish.

z

Never use hard objects or objects with
sharp edges to clean the interior walls
of the DHW tank.

Fig. 17

Hosing down the inside of the DHW tank

«
...
14
15
16
17
18
...
»

Содержание Logalux ST1000/3 US





















Отзывы:

Нет отзывов