background image

4  Description of function

20

K-425 / K-436

 Operation Manual, Version B

Description of function

This chapter explains the basic working principle of the SpeedDigester K-425 / K-436. It also shows 
how the instrument is structured and provides a general functional description of its assemblies.

4 .1 

Functional principle

The SpeedDigester K-425 / K-436 is a special heating device to digest samples. It can generate max. 
temperatures of 580 °C typically. This allows e.g. acid digestion of organic sample components in a 
concentrated sulfuric acid / catalyst mixture, known as 'Kjeldahl digestion'. During the processing the 
sample material can reach peak temperatures of up to 370 °C at the bottom area of the sample tubes. 
The maximum temperature of the sample highly depends on its composition i.e. the ratio of catalyst to 
acid and can change during the digestion process.

Digestion process overview

3

2

1

4

Environmental 
air inlet

dangerous vapors are drawn away

Condensing 
zone 

Infrared heating

Boiling / digesting 
sample

Insulation plate 
(fireclay insertion)

Acid vapor 
outlet to 
suction unit 
(e.g. Scrubber)

(

  5 cm)

Safety 
zone

Processing steps:
•  The infrared heating 

generates high temperatures in the sample.

•  Inside the sample tubes the digestion process takes place 

while the acid is constantly boiling.

•  Hot acid fumes rise into the condensing zone 

3

. After reflux, the acid flows back down to the 

sample material, establishing a constant cycle.

•  Residual fumes which escape the condensation zone are highly corrosive (!) and hazardous to life 

forms. It must be withdrawn by a suction unit that deliveres sufficient flow (i.e. with a Scrubber 
B-414 or a water jet pump) 

4

.

Note

The condensation should not take place inside the safety zone in order to prevent digestion of the 
sealing rings. In case the condensation is too close to the suction module (e.g. due to very high 
temperature settings) the digestion fumes may escape and the sample can dry out!

Содержание SpeedDigester K-425



























































Отзывы: