background image

2 Safety

8

B-90

 Operation Manual, Version B

2.3 

Improper use

Applications not mentioned in section 2.2 are considered to be improper. Applications which do not 
comply with the technical data (see section 3 of this manual) are also considered to be improper.

The operator bears the sole risk for any damages or hazards caused by improper use!

The following uses are expressly forbidden:
•  Use of gases with unknown chemical composition.
•  Spray drying of biohazard materials such as viruses or bacteria.
•  Spray drying of organic solvents in ‘open loop’ and without the Inert Loop B-295.
•  Installation or use of the instrument in rooms, which require ex-protected instruments.
•   Spray drying of substances which might explode or ignite due to the processing and the selected 

parameters of the Nano Spray Dryer B-90 or installed sub systems.

•  Use of samples which might produce oxygen during the processing.

2.4 

Safety warnings and safety signals used in this manual

DANGER, WARNING, CAUTION and NOTICE are standardized signal words for identifying levels of 
hazard seriousness of risks related to personal injury and property damage. All signal words, which are 
related to personal injury are accompanied by the general safety sign.

For your safety it is important to read and fully understand the below table with the different signal 
words and their definitions!

Sign Signal word Definition

Risk level

DANGER

Indicates a hazardous situation which, if not avoided, will 
result in death or serious injury.

★★★★

WARNING

Indicates a hazardous situation which, if not avoided, could 
result in death or serious injury.

★★★☆

CAUTION

Indicates a hazardous situation which, if not avoided, may 
result in minor or moderate injury.

★★☆☆

no

NOTICE

Indicates possible property damage, but no practices 
related to personal injury.

★☆☆☆

(property damage only)

Supplementary safety information symbols may be placed in a rectangular panel on the left to the 
signal word and the supplementary text (see below example).

Space for 

supplementary 

safety  

information 

symbols.

!

 

SIGNAL WORD

Supplementary text, describing the kind and level of hazard / risk seriousness.
•  List of measures to avoid the herein described, hazard or hazardous situation.
•  ...
•  ...

Содержание Nano B-90









































































































Отзывы: