background image

Büchi Labortechnik AG

Safety | 2

Operation Manual Inert Loop S-395

7/34

Operator

The operator (generally the laboratory manager) is responsible for the following
aspects:

—

The instrument must be correctly installed, commissioned, operated and serviced.

—

Only suitably qualified staff may be assigned the task of performing the
operations described in these operating instructions.

—

The staff must comply with the local applicable requirements and regulations for
safe and hazard-conscious working practices.

—

Safety-related incidents that occur while using the instrument should be reported
to the manufacturer ([email protected]).

BUCHI service technicians

Service technicians authorized by BUCHI have attended special training courses and
are authorized by BÜCHI Labortechnik AG to carry out special servicing and repair
measures.

2.4

Personal protective equipment

Depending on the application, hazards due to heat and/or corrosive chemicals may
arise.

u

Always wear appropriate personal protective equipment such as safety goggles,
protective clothing and gloves.

u

Make sure that the personal protective equipment meets the requirements of
the safety data sheets for all chemicals used.

2.5

Warning notices in this document

Warning notices warn you of dangers that can occur when handling the instrument.
There are four danger levels, each identifiable by the signal word used.

Signal word

Meaning

DANGER

Indicates a danger with a high level of risk which could result in
death or serious injury if not prevented.

WARNING

Indicates a danger with a medium level of risk which could result in
death or serious injury if not prevented.

CAUTION

Indicates a danger with a low level of risk which could result in mi-
nor or medium-severity injury if not prevented.

NOTICE

Indicates a danger that could result in damage to property.

2.6

Residual risks

The instrument has been developed and manufactured using the latest technological
advances. Nevertheless, risks to persons, property or the environment can arise if
the instrument is used incorrectly.
Appropriate warnings in this manual serve to alert the user to these residual
dangers.

Содержание Inert Loop S-395



































Отзывы: