BT LPE200 Скачать руководство пользователя | Manualshive

Страница: 83 / 154

background image

Electrical System – 5000 LWE 180/200 LPE 200

Parameters

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

© BT Europe AB

Service Guide

LWE180, LWE200, LPE200, LPE240

9- 45

Parameter 39

Login method and driver parameter access

This parameter determines which function is to be used for login and
whether the operator can adjust the driver parameter settings.

•

Value 1 – Key switch fitted – Driver parameters accessible (without
CAN service key).

•

Value 2 – Key switch fitted – Driver parameters NOT accessible
(without CAN service key).

•

Value 3 – Keypad (Standard 10 PIN code)- Driver parameters acces-
sible (without CAN service key) NB! this is the original setting.

•

Value 4 – Keypad (Standard 10 PIN code)- Driver parameters NOT
accessible (without CAN service key).

•

Value 5 – Expanded keypad (100 PIN code)- Driver parameters ac-
cessible (without CAN service key)

•

Value 6 – Expanded keypad (100 PIN code)- Driver parameters
NOT accessible (without CAN service key)

•

Value 7 – Expanded keypad (100 PIN code) + TLS- Driver parame-
ters accessible (without CAN service key)

•

Value 8 – Expanded keypad (100 PIN code) + TLS- Driver parame-
ters NOT accessible (without CAN service key)

Expanded keypad - General

The truck can contain a maximum of 10 individual driver profiles. The
expanded keypad function thus allows you to assign a maximum of 10
PIN codes for each of the driver profiles. This allows you to manage a
maximum of 100 unique PIN codes.

If the expanded keypad function is activated, the standard manage-
ment of PIN codes normally accessible via parameter #10 is set aside.

Expanded keypad - Programming

A number of PIN codes can be made accessible by activating the so-
called block. Block no. 0 is activated as standard. This means that 3 dif-
ferent driver profiles are available from the start. Activation of other
blocks means that all PIN codes for the block are accessible (See Table
5:). If all 10 blocks are activated, there will be 10 PIN codes available for
the driver profile.

The truck program stores a standard list of PIN codes as per Table 5:

These PIN codes can be changed to any value, but you should avoid
the same PIN code in different driver profiles.

«
...
81
82
83
84
85
...
»

Содержание LPE200



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPE200

Бренд: Hover-1 Страницы: 27

Бренд: KAUP Страницы: 21

Бренд: EKKO Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды