BT LPE200 Скачать руководство пользователя | Manualshive

Страница: 74 / 154

background image

9- 36

Service Guide

LWE180, LWE200, LPE200, LPE240

© BT Europe AB

Electrical System – 5000 LWE 180/200 LPE 200

Parameters

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

Changing configurable optional functions

In order to activate a configurable optional function, it must first be
assigned a parameter from #16 to #19. This is done by changing inde-
pendent variable #0 to the pre-programmed option number. Once this
has been done, the independent variable for the option must be config-
ured. This is done by changing the values for independent variables #1,
#2, #3 and #4.

•

Ensure the truck is in parameter mode.

The parameter symbol is lit.

•

Select parameter #16, #17, #18 or #19 using [L1].

Independent variable #0 is displayed

The independent variable value is displayed after 1 second. The value
“0” means that an optional function has not been assigned to this
parameter, and the speed control L1 in this case displays the next
parameter if you continue to activate it.

•

Press the horn button S18.

The parameter symbol flashes.

•

Enter the independent variable value #0 by repeatedly operating the
speed control L1 in either direction. See Table 2:

•

Press the S18 horn button once to confirm the new setting.

16 - 0 - 1

Parameter no. (range 16-19)

Independent variable: #0 is the option designation

Independent variable value (range 0-63)
0= no option has been activated for this parameter
1 to 63 = Pre-programmed option number. See separate table.)

16 - 1- 1

Independent variable: #1, #2, #3 & #4 contain the optional function valu

Independent variable value (the range depends on the function referred
The value depends on the option and independent variable selected.
See separate table

SETTING THE OPTIONAL FUNCTION

CONFIGURING THE OPTIONAL FUNCTION

Fig. 1

Summary – option parameter

«
...
72
73
74
75
76
...
»

Содержание LPE200



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPE200

Бренд: Jungheinrich Страницы: 157

Бренд: Ravas Страницы: 44

Бренд: Still Страницы: 518

Бренд: KAUP Страницы: 28

Бренд: Daewoo Страницы: 68

Бренд: Haklift Страницы: 30

Бренд: IMT Страницы: 135

CP LIGHT evo 030

Бренд: ARMANNI Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды