BT LPE200 Скачать руководство пользователя страница 68

Страница: 68 / 154

9- 30

Service Guide

LWE180, LWE200, LPE200, LPE240

Electrical System – 5000 LWE 180/200 LPE 200

Parameters

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

9.6 Parameters

•

Press and hold S18 while turning S17 to “ON” position.

•

Press and hold S18 until P = parameters is displayed.

•

You have now selected P = parameters and the symbol “C” is lit as
an indication of what is now shown in the display.

•

Press L1 up or down and scroll to the parameter you want to change
or view.

•

Press S18 once to access the parameter.

•

Press L1 up or down to specify the parameter value.

•

Press S18 once to confirm the change.

•

Turn S17 to the off position.

You have now changed the parameter and the new setting will come
into force the next time you start the machine.

NOTE:

Truck handling
When you change specific truck parameters, the truck’s driving char-
acteristics are also changed.
Do not change any parameters unless you really know what you are
doing.

9.6.1 Operator parameters

Parameter

Description

Unit

Min.

Max.

Step

Std.

Description

Speed, Turtle
button

100

Speed, Turtle button
10: slow speed
100: maximum speed.

Max. speed

100

Max. speed
10: slow speed
100: maximum speed

Acceleration

100

10: slow acceleration
100: maximum accelera-
tion

Braking in neu-
tral mode

100

Specifies motor braking
once the lever is put into
neutral.
5: weak braking power
100: maximum breaking
power

Logout

1min

The time it takes for the
truck to switch off when
the keypad is used. The
time counts down from
the moment the last
power-consuming unit is
used.

Value = 0 gives 4 hours.
In steps of 1

Содержание LPE200



























































































































































Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды

BT LPE200, Руководство по обслуживанию

Результаты поиска

Содержание LPE200

Отзывы:

Похожие инструкции для LPE200

Бренды по названию

Популярные бренды