BSR BSR00034 Скачать руководство пользователя | Manualshive

Страница: 58 / 133

background image

DS4800 REFERENCE MANUAL

44

4

4.2.2 RS485

Full-Duplex

Interface

The RS485 full-duplex (5 wires + shield) interface is used for non-polled communication
protocols in point-to-point connections over longer distances (max 1200 m / 3940 ft) than
those acceptable for RS232 communications or in electrically noisy environments.

The CBX pinout follows:

CBX100/500

Function

TX+

RS485 Transmit Data +

RX+

RS485 Receive Data +

TX-

RS485 Transmit Data -

RX-

RS485 Receive Data -

SGND Signal

Ground

RX485+

TX485+

SGND RX485- TX485-

USER INTERFACE

SGND TX+

RX+

TX- RX-

SCANNER

Figure 28 - RS485 Full-duplex Connections

NOTE

For applications that do not use RX485 signals, do not leave these lines
floating but connect them to SGND as shown below.

RX485+

SGND RX485-

USER INTERFACE

SGND TX+

TX-

SCANNER

Figure 29 - RS485 Full-duplex Connections using Only TX Signals

«
...
56
57
58
59
60
...
»

Содержание BSR00034






































































































































Отзывы:

Нет отзывов

Похожие инструкции для BSR00034

BA-440 DualBeam

Бренд: Bai Страницы: 29

HID iCLASS RWK400

Бренд: Assa Abloy Страницы: 12

QUICKSCAN 6000 PLUS

Бренд: Datalogic Страницы: 104

Бренд: Aiwa Страницы: 22

Бренд: Jadak Страницы: 83

Бренд: Lazerlogic Страницы: 55

Бренд: Symbol Страницы: 129

Бренд: Cognex Страницы: 17

Бренд: Panmobil Страницы: 34

Бренд: Clas Ohlson Страницы: 4

Бренд: Conceptronic Страницы: 21

Бренд: Intermec Страницы: 2

Бренд: Godex Страницы: 2

Бренд: Honeywell Страницы: 44

Gemplus 41N3005

Бренд: Lenovo Страницы: 42

Бренд: Argox Страницы: 34

Бренд: clare Страницы: 3

Бренд: Sunstech Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды