Bryant 580J*16D Series, Руководство по установке

Страница: 53 / 64

53
Table 24 — RTU Open Controller Inputs and Outputs
LEGEND
1. Safety Chain Feedback: 24Vac required at this terminal to provide “Run Enable” status. See Input/Output section for additional instructions.
2. These inputs are configurable. If installed, they take the place of the default input on the specific channel. See appropriate Input Configuration Section
for wiring and setup instructions.
3. Refer to the input configuration and accessory sections of the RTU Open Multi–Protocol Controller Controls, Start–Up, Operation and Troubleshooting
manual for more detail.
4. Parallel pins J5–1 = J2–6, J5–3 = J1–10, J5–5 = J1–2 are used for field installation.
POINT NAME
BACNET OBJECT
NAME
TYPE OF I/O
CONNECTION
PIN NUMBER (S)
CHANNEL DESIGNATION
DEDICATED INPUTS
Space Temp / Zone Temp
zone_temp AI (10K Thermistor) J20–1 and 2 Analog Input 10
Supply Air Temperature
sa_temp AI (10K Thermistor) J2–1 and 2 Analog Input 6
Outside Air Temperature
oa_temp AI (10K Thermistor) J2–3 and 4 Analog Input 7
Space Temperature Offset Pot
stpt_adj_offset
AI(100K
Potentiometer)
J20–3 and 4 Analog Input 11
Safety Chain Feedback
safety_status BI (24 VAC) J1–9 Binary Input 4
Compressor Safety Status 1
comp_status BI (24 VAC) J1–2 Binary Input 3
Fire Shutdown Status
firedown_status BI (24 VAC) J1–10 Binary Input 5
Enthalpy Status
enthalpy_status BI (24 VAC) J2–6 and 7 Binary Input 8
Humidistat Input Status
humstat_status BI (24 VAC) J5–7 and 8 Binary Input 9
Zone Temperature
n/a n/a J13–1–4 Rnet
CONFIGURABLE INPUTS 4
Indoor Air CO
2
iaq AI (4–20 mA)
J4–2 and 3 or J4–5
and 6
Analog Input 2
Outdoor Air CO
2
oaq AI (4–20 mA) Analog Input 1
Space Relative Humidity
space_rh AI (4–20 mA) Analog Input 10
Supply Fan Status 2
sfan_status BI (24 VAC)
J5–1 and 2 or
J5–3 and 4, J5–5
and 6 or J5–7 and
8
3
Binary Input 3, 5, 8, or 9, except where
intrinsic input is used
Filter Status 2
filter_status BI (24 VAC)
Binary Input 3, 5, 8, or 9, except where
intrinsic input is used
Door Contact 2
door_contact_status BI (24 VAC)
Binary Input 3, 5, 8, or 9, except where
intrinsic input is used
Remote Occupancy Input 2
occ_contact_status BI (24 VAC)
Binary Input 3, 5, 8, or 9, except where
intrinsic input is used
IGC Input 2
igcovr_status BI (24 VAC)
Binary Input 9. Mandatory input on gas
heat units.
OUTPUTS
Economizer Output
econ_output AO (4–20mA) J2–5 Analog Output 1
Supply Fan VFD
vfd_output AO (2–10Vdc) J22–1 and 2 Analog Output 2
Supply Fan Relay
sfan BO Relay (24VAC, 1A) J1–4 Binary Output 1 (G)
Cool 1 Relay State
comp_1 BO Relay (24VAC, 1A) J1–8 Binary Output 5 (Y1)
Cool 2 Relay State
comp_2 BO Relay (24VAC, 1A) J1–7 Binary Output 4 (Y2)
Cool 3 Relay State
comp_3 BO Relay (24VAC, 1A) J11–5 and 6 Binary Output 7 (Y3)
Heat 1 Relay State
heat_1 BO Relay (24VAC, 1A) J1–6 Binary Output 3 (W1)
Heat 2 Relay State
heat_2 BO Relay (24VAC, 1A) J1–5 Binary Output 2 (W2)
Power Exhaust Relay State
pexh BO Relay (24VAC, 1A)
J11–2 and 3
(N.O.)
Binary Output 8 (PE)
Dehumidification Relay
dehum BO Relay (24VAC, 1A)
J11–7 and 8
(N.O.)
Binary Output 6
AI — Analog Input
AO — Analog Output
BI — Binary Input
BO — Binary Output