manualshive.com logo in svg

Bryant 580J*04A, Руководство по установке

Поделиться
Скачать
Bryant 580J*04A Скачать руководство пользователя страница 3

3

Fig. 1 — 580J*04-07 Units Model Number Nomenclature

Note: On single phase (-J voltage code) models, the
following are not available as a factory installed option:

- Coated Coils or Cu Fin Coils
- Louvered Hail Guards
- Economizer or 2 Position Damper
- Powered 115 Volt Convenience Outlet

Model

J -  Puron

®

 (R-410A) Refrigerant

Unit Type

580  -  Gas Heat RTU
  

Legacy™ 

Series

Packaging & 2-Speed Indoor Fan Motor

A  =  Standard Packaging, electro mech. controls
   

that require W7212 EconoMi$er

®

 IV

B  =  LTL Packaging, electro mech. controls
   

that require W7212 EconoMi$er IV

C  =  Standard Packaging, electro mech. controls
   

that require W7220 EconoMi$er X

F  =  LTL Packaging, electro mech. controls
   

that require W7220 EconoMi$er X

Cooling Tons

04 -  3 tons
05 -  4 tons
06 -  5 tons
07 -  6 tons

Heat Level

Standard/Stainless Steel
072 =  72,000
115 = 115,000
125 = 125,000
150 = 150,000

Low NOx
060 =  60,000
090 =  90,000
120 = 120,000

Indoor Fan Options

0  =  Direct Drive, Standard Staitc Option (04/05/06 models only)
1  =  Belt Drive, Standard Static Option
2  =  Belt Drive, Medium Static Option
3  =  Belt Drive, High Static/ Option

Refrig. System/Gas Heat Options

A  =  Standard One Stage cooling models/Natural Gas Heat
B  =  Standard One Stage cooling models/Low NO

x

 Heat

C  =  Standard One Stage cooling models/Stainless Steel HX Heat
G =  One Stage cooling models/Alum Heat Exchanger
   

with Perfect Humidity™ (07 models only)

J  =  One Stage cooling models/Stainless Steel Exchanger
   

with Perfect Humidity™ (07 models only)

Coil Options For Round Tube/Plate Fin Condenser Coil Models Only 
(Outdoor - Indoor - Hail Guard)

A  =  Al/Cu - Al/Cu
B  =  Precoat Al/Cu - Al/Cu
C  =  E-coat Al/Cu - Al/Cu
D  =  E-coat Al/Cu - E-coat Al/Cu
E  =  Cu/Cu - Al/Cu
F  =  Cu/Cu - Cu/Cu
M =  Al/Cu -Al/Cu — Louvered Hail Guard
N  =  Precoat Al/Cu - Al/Cu — Louvered Hail Guard
P  =  E-coat Al/Cu - Al/Cu — Louvered Hail Guard
Q =  E-coat Al/Cu - E-coat Al/Cu — Louvered Hail Guard
R  =  Cu/Cu - Al/Cu — Louvered Hail Guard
S  =  Cu/Cu - Cu/Cu — Louvered Hail Guard

Coil Options For All Aluminum - Novation Condenser Coil Models Only 
(Outdoor - Indoor - Hail Guard)

G =  Al/Al - Al/Cu
H  =  Al/Al - Cu/Cu
J  =  Al/Al - E-coat Al/Cu
K  =  E-coat Al/Al - Al/Cu
L  =  E-coat Al/Al - E-coat  Al/Cu
T  =  Al/Al - Al/Cu — Louvered Hail Guard
U  =  Al/Al - Cu/Cu — Louvered Hail Guard
V  =  Al/Al - E-coat Al/Cu — Louvered Hail Guard
W =  E-coat Al/Al - Al/Cu — Louvered Hail Guard
X  =  E-coat Al/Al - E-coat Al/Cu — Louvered Hail Guard

Voltage

E =  460-3-60
J = 208/230-1-60
P =  208/230-3-60
T =  575-3-60

Example:

Position:

5

8

0

J

E

0

6

A

0

7

2

A

1

B

0

A

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Factory Installed Options

0A = 

None

  

NOTE: 

See the 580J 3 to 15 ton Price Pages for a 

 

   

complete list of factory installed options.

Outdoor Air Options

A =  None
B  =  Temperature Economizer, Barometric Relief,
   

Standard Leak (W7212 or W7220)

E  =  Temperature Economizer, Barometric Relief,
   

Standard Leak w/CO

2

, (W7212 or W7220)

H =  Enthalpy Economizer, Barometric Relief,
   

Standard Leak, (W7212 or W7220)

L =  Enthalpy Economizer,Barometric Relief,
   

Standard Leak w/CO

2

, (W7212 or W7220)

Q =  Motorized 2 Position Damper
U =  Temperature Economizer, Barometric Relief,
   

Ultra Low Leak, (W7220)

W =  Enthalpy Economizer, Barometric Relief,
   

Ultra Low Leak, (W7220)

Содержание 580J*04A





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды