background image

6

WHEN ADDING FUEL

• Turn off engine and let cool at least 2 minutes before removing the fuel 

cap and adding fuel.

•  Fill fuel tank outdoors or in a well ventilated area.
• Do not overfill the fuel tank. To allow for the expansion of gasoline, do not fill

above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other 

ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks. Replace if 

necessary.

• Use an approved fuel container.
• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

•  Ensure that spark plug, muffler, fuel cap, and air cleaner (if equipped) are in 

place and secured.

•  Do not crank the engine with the spark plug removed.
•  If fuel is spilled, do not attempt to start the engine, but move the snow 

thrower away from the area of the spill, and avoid creating any source of 
ignition, until the fuel vapors have dissipated. 

• Do not over-prime the engine. Follow the engine starting instructions in this 

manual.

•  If the engine floods, set choke (if equipped) to OPEN/RUN position, move 

throttle (if equipped) to FAST position and crank until engine starts.

WHEN OPERATING EQUIPMENT

•  Do not tip the snow thrower at an angle which causes the fuel to spill.
• Do not choke the carburetor to stop the engine.
• Never run the engine with the air cleaner assembly (if equipped) or the air 

filter (if equipped) removed.

WHEN CHANGING OIL

•  If you drain the oil from the top oil fill tube, the fuel tank must be empty or 

fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

•  Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

•  Store away from furnaces, stoves, water heaters, or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable and explosive.
Always handle fuel with extreme care.   
Failure to observe these safety instructions can cause a fire 
or explosion which will result in severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small children 

and pets.

• Thoroughly inspect the area where the snow thrower will be used and remove

all doormats, sleds, boards, wires, and other foreign objects.

• Do not operate the snow thrower without wearing adequate winter clothing.
• Wear footwear that will improve footing on slippery surfaces.
•  Use caution to avoid slipping or falling especially when operating the 

snow thrower in reverse.

• Never operate the snow thrower without good visibility or light. Always be 

sure of your footing, and keep a firm hold on the handles.  

• Do not clear snow across the face of slopes. Use extreme caution when 

changing direction on slopes. Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to clear snow too 

quickly.

• Never operate the snow thrower at high transport speeds on slippery 

surfaces. Look behind the snow thrower and use care when operating in 
reverse.  

• Do not use the snow thrower on surfaces above ground level such as roofs of

residences, garages, porches, or other such structures or buildings.

• Operators should evaluate their ability to operate the snow thrower safely 

enough to protect themselves and others from injury.

• The snow thrower is intended to remove snow only. Do not use the snow 

thrower for any other purpose.

• Do not carry passengers.
• After striking a foreign object, shut OFF the engine, disconnect the cord on 

electric motors, thoroughly inspect the snow thrower for any damage, and 
repair the damage before restarting and operating the snow thrower.

• If the snow thrower vibrates abnormally, shut OFF the engine. Vibration is 

generally a warning of trouble. See an authorized dealer if necessary for 
repairs.

• For models equipped with electric starting motors, disconnect the power 

cord after the engine starts.

DANGER

This  snow  thrower  is  only  as  safe  as  the  operator.  If  it  is
misused,  or  not  properly  maintained,  it  can  be  dangerous.
Remember  you  are  responsible  for  your  safety  and  that  of
those around you.

Operation and Equipment Safety

OPERATOR SAFETY

Not 

for  

Reproduction

Содержание 1695724

































































Отзывы: