Bruker NMR 400 89 Ascend DNP Скачать руководство пользователя страница 48

Страница: 48 / 106

ZTKS0243 / Z31993 / 03

Troubleshooting

6.2.4

During Energizing and Shimming

Continued on next page

Indicator

Possible reason

Solution

The current lead can
not be inserted
completely into the
connector.

The connector is
covered with ice
(frozen moisture or
nitrogen ice).

Carefully remove the ice with
warm helium gas.

Use the dipstick or the
precooling tube as tubing for
the warm helium gas to
remove small ice spots.

Bruker Service

The shorting plug
was not removed.

Remove the shorting plug
with the shorting plug tool.

Bruker Service

The orientation of
the current lead is
not correct.

Turn the current lead carefully
until it can be inserted
correctly into the connector.

Bruker Service

Main coil heater test
fails.

Defective Power
Supply.

Replace the Power Supply

Bruker Service

Connector or cables
defective.

Clean connectors or replace
cables if necessary.

Bruker Service

Setting of sense
voltage fails.

The main coil heater
switch is "OFF".
The main coil switch
is not opened.

Switch the main coil heater to
"ON" and check the main coil
heater current to be adjusted
correctly.

Bruker Service

The main coil heater
current is not
correct. The main
coil switch is not
opened.

Adjust main coil heater
current correctly.

Bruker Service

The auxiliary short-
ing plug is inserted in
the current lead
turret by mistake and
makes a short circuit
across the main coil.

Remove the auxiliary shorting
plug and insert it in the helium
fill-in turret.

Bruker Service

Current lead can not
be removed.

The connector is
covered with ice
(frozen moisture or
nitrogen ice).

Carefully remove the ice with
warm helium gas over the
helium flow system. Use the
dipstick or the precooling tube
as tubing for the warm helium
gas to remove small ice spots
from the connector.

Bruker Service

Содержание NMR 400 89 Ascend DNP











































































































Результаты поиска

Содержание NMR 400 89 Ascend DNP

Отзывы:

Bruker NMR 400 89 Ascend DNP, Руководство пользователя, Страница: 48 / 106

Результаты поиска

Содержание NMR 400 89 Ascend DNP

Отзывы: