Bruker minispec mq20 Скачать руководство пользователя страница 69

Страница: 69 / 86

minispec.exe Software for Diagnostic and Service Purposes

E1400912_1_001

Some of the functions described might only be available in certain minispec.exe software
versions.

8.3.8

The Process Menu

The

Process

item is only displayed when a Signal Window is active. Different commands for

data processing are summarized in this pull-down menu:

Figure 8.15: The Process Pull-Down Menu

Within the context not all commands may be reasonable, in which case they will be grayed.
The following series of built-in signal processing features are available:

The Fit Command

This command is only available in connection with calibrations. You can fit your calibration
data and display the fit results (see

Info Views

, point 4).

The FFT, Magnitude, Power and Absolute Commands

A Fast Fourier Transform of measurement data will be performed using the

FFT

command. If

the NMR signal is observed in complex mode (real and imaginary part of the signal) the

Magnitude

([Re2+Im2]1/2) or the power spectrum can be calculated. From the real,

imaginary or complex data, the

Absolute

values can be calculated.

The Signal Flip, and the Signal Swap Command

The signal can be mirrored with respect to an offset frequency of 0 using the

Signal Flip

command. The

Signal Swap

command exchanges the real and imaginary part.

Содержание minispec mq20























































































Результаты поиска

Содержание minispec mq20

Отзывы:

Bruker minispec mq20, Руководство пользователя, Страница: 69 / 86

Результаты поиска

Содержание minispec mq20

Отзывы: