Bruker minispec mq20 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 86

Bruker minispec mq20 Скачать руководство пользователя страница 31

Getting Started

E1400912_1_001

31

6

Getting Started

In general, minispec systems which are delivered with a personal computer already have the
minispec software installed and are fully pre-configured. In this case, the user can skip the
software installation and configuration, and proceed directly to the operational part.

The mq20 Toothpaste Analyzer operates with the minispec Plus software and with the well-
known minispec.exe software running in the background as an acquisition server. The
practical use of the software is illustrated in

Running the minispec mq20 Toothpaste Analyzer

. Moreover, the manual

minispec Plus Administration

, together with the

manual

minispec Plus Classic

, provide further details on the minispec software GUI. These can be

found on the minispec software CD/memory stick in the folder

Documentation

.

In general systems equipped with minispec Plus software do not necessarily need to start the
minispec.exe  software  before  using  minispec  Plus.  If  the  system  is  properly  installed,  then
minispec  Plus  can  be  opened  without  first  opening  the  minispec.exe  software.  However  in
some cases (like when the system was not shipped from Bruker directly) it might be useful to
first  run  the  minispec.exe  software  to  make  sure  there  is  a  proper  network  connection  from
PC to the minispec, then afterwards switch to the minispec Plus program.

When a user provides their own personal computer, or if software needs to be reinstalled for
use with the minispec, refer to the installation instructions below.

6.1

Software Installation

Execute the following steps if the PC has not been pre-configured for the minispec by
Bruker.

Please  note  that  for  proper  installation  of  the  minispec  software,  PC  system  requirements
apply.  For  minispec  Plus  operation,  in  addition  to  the  specified  Microsoft  operation  system
version,  which  is  required  for  minispec.exe  software  operation,  Microsoft  Office  is  required
too.  Each  minispec  software  and  software  installation  is  released  for  one  combination  of
Windows operating system and Microsoft Office version. Ensure that the correct combination
is  pre-installed  on  the  PC.  For  further  details,  refer  to  the  corresponding  minispec  Plus
manual.

To install the software, the following steps are needed:

1. Insert the installation CD in your drive, or when using a memory stick, insert the stick in a

USB port.

2. Open the Windows EXPLORER and check the media for a ReadMe.txt file. If a

ReadMe.txt file is available, follow the instructions provided in this file.

3. If not, execute the

Setup

file with a double click or select the setup entry with the right

mouse button and select

Open

in the displayed menu.

4. Follow the instructions in the

Setup

program.

´

The

Setup

program copies the files into the folder you specify during the setup

procedure.

5. To start the minispec.exe software, double click on the minispec.exe file in the main

folder. Alternatively, you can create a shortcut on the Windows desktop to the file
minispec.exe.

Note:

Systems that are equipped with minispec Plus software will install this additional GUI
program automatically. In this case an

.ini

file will carry the corresponding licenses and the

installation software will recognize known licenses and install the software GUI accordingly.

«
...
29
30
31
32
33
...
»

Содержание minispec mq20























































































Отзывы:

Нет отзывов