BRP Evinrude E-TEC Series Скачать руководство пользователя страница 327

Страница: 327 / 342

TROUBLE CHECK CHART

OUTBOARD STARTS, LOW MAXIMUM RPM

T–5

OUTBOARD STARTS, LOW MAXIMUM RPM

EXCESSIVE SMOKING

OBSERVATION

POSSIBLE CAUSE

PROCEDURE

SystemCheck

light

Outboard is in

S.A.F.E.

Check

ervice Codes and

SystemCheck

warning

Setup or rigging
change

Incorrect propeller

Refer to specifications,

check recommended WOT

RPM; water test and install correct pitch propeller

Incorrect outboard mounting
height

Refer to installation guidelines

Performance of
outboard at lower
speeds appears
normal

Incorrect, fouled, or worn spark
plugs

Replace spark plugs

Contaminated or poor quality
fuel

Check or replace fuel supply

Fuel supply restricted

Check primer bulb, anti-siphon valve, and fuel
pick-up, check for fuel system air leaks

Low alternator output (55 V)

Check voltage on 55 V circuits, refer to

SYSTEM

ANALYSIS

and

ELECTRICAL AND IGNITION

Weak or erratic ignition
operation

Check ignition, refer to

SYSTEM ANALYSIS

and

ELECTRICAL AND IGNITION

Fuel injector electrical circuit or
control function

Check voltage at injectors, refer to

SYSTEM

ANALYSIS

Restricted or leaking fuel
injectors

Check injectors, refer to

FUEL SYSTEM

Low fuel pressure

Check circulation pump operation, refer to

FUEL

SYSTEM

EMM

programming, timing, or

operation

Check

EMM

program and timing;

check injector

coefficients; and monitor injector circuits and
ignition primary outputs

Restricted engine exhaust

Check and repair as needed

OBSERVATION

POSSIBLE CAUSE

PROCEDURE

May coincide with
increased oil
consumption
(normal if occurs after
winterization)

Contaminated or poor fuel
quality

Check or replace fuel supply

Excessive fuel or oil
consumption

Check fuel system for fuel supply air leaks or
leaking fuel injectors

Outboard in break-in mode

Use diagnostics program to

check

Outboard mounted too low

Check installation height of outboard

Vapor separator vent

Check vapor separator assembly for proper
venting/float valve operation

Faulty/leaking fuel injector(s)

Check injectors, refer to

FUEL SYSTEM

Damaged fuel lift pump

Check for internal leaks

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 327 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: