manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 28 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 28

26

ROUTINE SERVICE

ADJUSTMENTS

Shift the engine from NEUTRAL to FORWARD
gear. The Neutral/In Gear indicator must indicate
“In Gear.”

Shift the engine from FORWARD gear to NEU-
TRAL. The Neutral/In Gear indicator must indicate
“Neutral.”

Shift the engine from NEUTRAL to REVERSE
gear. The Neutral/In Gear indicator must indicate
“In Gear.”

Shift the engine from REVERSE gear to NEU-
TRAL. The Neutral/In Gear indicator must indicate
“Neutral.”

Readjust the neutral switch and confirm neutral
switch operation if the Neutral/In Gear indicator
does not match engine shift position.

Trim Sending Unit Adjustment

The sending unit eccentric cam must be adjusted
so that the gauge needle is aligned with the lowest

gauge mark with the outboard trimmed all the way
DOWN.

Check if the gauge needle is above or below the
lowest gauge mark. Tilt engine UP and engage
trailering lock.

When the outboard is trimmed all the way DOWN,
the sending unit lever touches the eccentric cam
just forward of the top of the cam at the contact
point.

Loosen cam screw and rotate eccentric cam to
adjust full down gauge position:

•

If the needle was above the lowest mark, move
the thick part of the cam TOWARD the contact
point. Tighten the screw, and recheck the gauge
reading.

1.

Monitor screen

2.

Neutral/In Gear indicator

008137

2

1

1.

Lowest gauge mark

DR2827

1.

Trailering lock

18954

WARNING

To avoid personal injury, do not adjust the
sending unit eccentric cam while the
engine is being tilted.

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов