manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 275 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 275

273

TRIM AND TILT

TRIM AND TILT REPLACEMENT

13

Trim Sender Test

IMPORTANT:

To avoid immediate meter dam-

age, never apply an ohmmeter to an electrical cir-
cuit where voltage is present.

Disconnect the 3-pin connector between the
instrument harness and engine trim harness.
Connect an ohmmeter between the white/tan wire,
terminal “C,” of the engine harness and a clean
engine ground.

With the outboard fully DOWN, meter must show
a reading above 80 ohms.

With the outboard fully UP, meter must show a
reading below 10 ohms.

•

If results agree, refer to 

Trim Gauge Test

 on

p. 272.

•

If results are different, replace trim sender.

TRIM AND TILT 
REPLACEMENT

Removal

Raise the outboard and engage the tilt support.

Remove the rubber grommet from the blue/green
trim/tilt cable connector.

Remove the terminals from the connector by
using a suitable tool to depress the tab. While the
tab is depressed, pull on the wire from the rear of
the connector to release it from the connector.

Separate the trim/tilt unit wires in the braided tube
to permit removal through the hole in the stern
bracket.

DRC6247

000686

000687

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов