manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 271 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 271

269

TRIM AND TILT

SYSTEM DESCRIPTION

13

SYSTEM DESCRIPTION

The power trim/tilt hydraulic system is completely
contained between the outboard's stern brackets.

The system consists of:

•

Electric motor

•

Oil reservoir

•

Pump manifold assembly

•

Cylinder body assembly 

Optimal boat and outboard performance can be
achieved by adjusting (trimming) the angle of out-
board propeller thrust. The first 15° of outboard
movement is considered trim range.

Outboard movement beyond the trim range is
considered tilting. Tilting of the outboard may be
desired for shallow water drive and for traile-
ring/storage. The tilt cylinder moves the outboard
through the tilt range.

IMPORTANT:

 When in tilt range, make sure

water is available to gearcase water pickups.

Manual Adjustment

The outboard can be manually raised or lowered
through its entire trim and tilt range by opening the
manual release valve a minimum of three turns.
When this cycle is complete, the manual release
valve must be closed and tightened to a torque of
45 to 55 in. lbs. (5 to 6 N·m) before normal opera-
tion can be resumed.

Trailering Bracket And Tilt 
Support

These outboards are equipped with combination
tilt support/trailering brackets.

Tilt the outboard up fully, engage the bracket, then
tilt the outboard down until the bracket is firmly in
position.

1.

Manual release valve, 40-60 HP

008018

1

1.

Trailering locks

007636

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов