manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 260 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 260

258

GEARCASE

BEARING AND SEAL INSTALLATION

Propeller Shaft Bearing Housing 
Seals and O-ring

Remove and discard the propeller shaft bearing
housing O-ring.

Use Puller Bridge, P/N 432127, and Small Puller
Jaws, P/N 432131, to remove seals. Discard
seals.

Use Puller Bridge, P/N 432127, and Small Puller
Jaws, P/N 432131, to remove both propellers
shaft bearings from the bearing housing. Discard
both bearings.

BEARING AND SEAL 
INSTALLATION

IMPORTANT:

Make no dry assemblies. Lubri-

cate all bearings, shafts, and gears with gearcase
lubricant.

Press the bearings into the housings until the
tools are seated on the housing.

Propeller Shaft Bearing 
Housing Bearings

Use Bearing Installer, P/N 335820, to install a new
bearing in the rear end of bearing housing. Posi-
tion installer against the lettered side of bearing.
Press the bearing into the housing until the tool is
seated on the housing.

Use Bearing Installer, P/N 321428, to install a new
bearing in the forward end of the bearing housing.
Position installer against the lettered side of bear-
ing.

1.

O-ring

007680

1.

Small puller jaws

32555

1.

Small puller

21795

1

1

1

21793

21794

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов