manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 223 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 223

221

MIDSECTION

STERN BRACKET – MANUAL TILT MODELS

11

Stern Bracket Assembly (Manual 
Tilt)

Install a new bushing through hole in tilt lock
assembly. Press bushing into swivel bracket until
fully seated. Make sure tilt lock assembly moves
freely.

IMPORTANT:

Prevent damage to the tilt lock

assembly stop pin. Be sure to properly support the
swivel bracket when pressing in bushings.

Assemble reverse lock link and reverse lock lever
as shown. Install pin and secure with new cotter
pin.

Place pin through the shallow water drive link as
shown. Secure with new cotter pin. 

Align reverse lock link assembly with shallow
water drive link as shown. 

1.

Stop pin

007629

1.

Tilt lock assembly

2.

Correct support

007603

1

2

1

1.

Reverse lock link

2.

Reverse lock lever

3.

Pin

007604

1.

Shallow water drive link

2.

Pin

007630

1.

Reverse lock link assembly

2.

Shallow water drive link

007605

1

2

3

1

2

1

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов