BRP Evinrude E-TEC Series Скачать руководство пользователя страница 186

Страница: 186 / 342

184

POWERHEAD

POWERHEAD ASSEMBLY

Test that the crankshaft spins freely without bind-
ing.

IMPORTANT:

After powerhead has been

assembled, allow at least two hours for

Gel-Seal II

to cure before running outboard.

Apply

Gasket Sealing Compound

to both sides of

new inner and outer exhaust cover gaskets. Posi-
tion gaskets and covers on cylinder block.

Apply

Nut Lock

to cover screws. Tighten all

screws in sequence, to a torque of 84 to 106 in.
lbs. (9.5 to 12 N·m).

Cylinder Head Installation

Apply soapy water to water dam and insert into
block.

Place a new cylinder head gasket on alignment
pins.

Install cylinder head with the thermostat toward
the top. Apply

Triple-Guard

grease to the threads

and install the cylinder head screws. DO NOT use
any sealant on threads

Inner exhaust cover

Outer exhaust cover

007768

007769

Water dam tab

007770
007771

Alignment pins

007772

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 186 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: