BRP Evinrude E-TEC Series Скачать руководство пользователя страница 142

Страница: 142 / 342

140

FUEL SYSTEM

FUEL COMPONENT SERVICING

Prime screw threads with

Locquic Primer

and let

dry. Apply

Ultra Lock

to threads. Position reed

valve on reed plate and install screws. Tighten
screws to a torque of 35 to 60 in. lbs. (4.0 to 6.8
N·m).

Installation

Place reed plate assembly on cylinder/crankcase.

Apply

Nut Lock

to reed plate screws. Install and

tighten screws to a torque of 84 to 106 in. lbs. (9.5
to 12 N·m).

Place gasket on throttle body. Install throttle body
on reed plate and install

new

screws.

IMPORTANT:

If old screws must be re-used,

make sure all previous thread locking material is
removed and apply

Nut Lock

to threads.

Tighten the center screws first and expand out-
ward. Tighten in stages to a final torque of 84 to
106 in. lbs. (9.5 to 12 N·m).

Install vapor separator vent hose and main bear-
ing vent hose. Secure with tie straps.

Install crankshaft position sensor, and throttle
position sensor electrical connectors.

Connect throttle linkage.

IMPORTANT:

DO NOT lubricate throttle link-

ages.

Refer to

TPS Calibration

on p. 106.

007432

007433

007434

Throttle linkage

007435

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 142 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: